Macdon 9352c SP User Manual Page 42
- Page / 155
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 147459 Issue 11/06 Web Rev_01
40
OPERATION
Attaching the Header
1. Choose an area that is as level as possible and
set header stand (A) in the down position.
942 Header
, set 2 inch (50 mm) blocks under
each end of cutterbar.
960 & 970 Series Headers, be sure header and
tractor have been properly prepared for
windrower use.
See "Preparing Tractor and Headers" in
Assembly section for details.
CAUTION: Be sure area is clear of
bystanders, then start engine.
2. Fully retract header lift cylinders. For units with
Header Express Down option, use switch on
side console to bypass the feature.
NOTE: For 30’ & 36’ Harvest Headers with
Transport Option; when attaching to header in
transport mode, position 6 inch high (150 mm)
blocks for drive tires to provide adequate linkage
height. Blocks should be at least the width of the
drive tires and long enough that drive tires are fully
supported when attaching header.
3. Slowly drive tractor forward so that lift linkage
enters header legs. Continue to drive slowly
forward until linkage contacts support plate in
the lower header leg, and header nudges
forward. Place variable speed lever into neutral
position and lock steering wheel. Stop engine
and remove key.
4. Adjust length of center link and connect to
header at (C). For 962 and 972 headers, use
the lower, more rearward hole in mount on
header tube as shown.
NOTE: Ensure that thread length is equal at
both ends of center link. See "Header Angle for
adjustment details.
5. Check that bottom of linkage (D) is properly
engaged in header leg, contacting support plate
(E).
NOTE: For Harvest Headers with gauge
wheels, instructions under "Attaching" and
"Detaching the Header" which refer to the
"header stand" do not apply. Use the "stand"
position of the gauge wheels to support rear of
header. All gauge wheel positions are identified
on a decal located at each gauge wheel. Be
sure to reposition gauge wheel to field position
before operating.
INSTALL CENTER LINK
CHECK FOR PROPER ENGAGEMENT
A
HEADER STAND - DOWN POSITION
963 HEADER STAND
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- MAINTENANCE/SERVICE 62
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine: Fuel System 72
- Engine Exhaust System 77
- Engine Cooling System 78
- Electrical System 81
- Hydraulic System 90
- Header Drive: Hydraulics 93
- Traction Drive: Hydraulics 98
- Steering Checks 99
- MAINTENANCE/SERVICE 100
- Steering Checks (continued) 100
- MAINTENANCE/SERVICE 101
- Troubleshooting 102
- Procedure (continued) 104
- Friction Device Adjustment 105
- Cab Air System 109
- Maintenance Schedule 112
- MAINTENANCE RECORD 114
- (continued) 115
- TROUBLE SHOOTING 116
- Electrical 124
- Traction Drive System 125
- Header Hydraulics 128
- Header Drive 128
- TROUBLE SHOOTING 129
- Header Drive (continued) 130
- Park Brake 130
- Operator's Seat 130
- OPTIONS AND ATTACHMENTS 131
- B2961 – Fore-Aft 131
- B2962 – Header Tilt 131
- UNLOADING 132
- Prepare to Unload 132
- Two Forklift Method 132
- UNLOADING 133
- One Forklift Method 133
- ASSEMBLY 134
- Install Tires 134
- ASSEMBLY 135
- Battery 136
- ASSEMBLY 137
- Adjustments and Checks 137
- Cab Heater 137
- Preparing the Tractor for 138
- 962/963 & 972 Headers 138
- Preparing 972 Harvest Header 141
- Radio Installation 142
- Two-Way Radio Installation 143
- Tool Box 143
- Swath Roller 144
- Self-Propelled Windrower 149
- Pre-Delivery Checklist 149
- Roof Wiring Schematic 151
- Cab Wiring Schematic 152
- Tractor Wiring Schematic 153
- Form 147141/147459 154
Related products and manuals for Gardening equipment Macdon 9352c SP
Gardening equipment Macdon 9352i SP User Manual
(155 pages)
(155 pages)
Gardening equipment Macdon 9250 SP User Manual
(160 pages)
(160 pages)
Gardening equipment Macdon D65 User Manual
(166 pages)
(166 pages)
Gardening equipment Macdon D65 User Manual
(42 pages)
(42 pages)
Gardening equipment Macdon A-30D User Manual
(140 pages)
(140 pages)
Gardening equipment Macdon A40-D User Manual
(193 pages)
(193 pages)
© 2020, manymanuals.com. All rights reserved. | 1.359 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals