Macdon 9352c SP User Manual Page 52
- Page / 155
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 147459 Issue 11/06 Web Rev_01
50
OPERATION
Header Flotation
The following suggested header float settings are a starting point for normal conditions
. Your specific
requirements and conditions may require heavier or lighter float.
Force required to lift the cutterbar off ground at each end of the header (with lift cylinders fully retracted):
910/920/932 Auger Headers: 100 to 120 lbs. (445 - 535 N)
912/922/933 Auger Headers & 942 Multi-Crop Header: 75 to 85 lbs. (335 - 380 N)
Draper Headers: 50 to 70 lbs. (220 - 310 N)
Benefits of lighter float settings
:
1. Less cutting component breakage in rough or stony conditions.
2. Avoids soil build-up at cutterbar in wet conditions.
Benefits of heavier float settings
:
1. When cutting very close to the ground, enables the cutterbar to follow ground contours.
NOTE: For all headers except 12’ & 15’ 972
Header, use top hole (A) in float linkage. For 12’ &
15’ 972 Header, use lower hole (B).
To adjust header float:
NOTE: Because of end-to-end weight differential,
dimension (C) at left and right drawbolt will be
different to achieve equal float at both ends of
header. Also, lighter headers will require a larger
dimension (C), heavier headers a smaller
dimension (C).
1. Raise header fully, shut off engine, remove key.
2. Loosen nut (D).
3. Turn spring drawbolt (E) clockwise to increase
float (which makes header lighter when lowered
to ground).
Turn bolt counter-clockwise to decrease
float
(which makes header heavier when lowered).
4. Tighten nut (D) to lock position.
5. Lower header fully and check float at both ends
of cutterbar. Force required to lift cutterbar
should be approximately the same at both ends.
IMPORTANT: Spring loaded gauge wheels
(available on some draper headers) have an
effect on header float. See “Header Floatation”
in your header operator’s manual for details.
E
C
D
FLOAT ADJUSTMENT
A
USE HOLE “B” FOR 12’ & 15’ 972 HEADER
B
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- MAINTENANCE/SERVICE 62
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine: Fuel System 72
- Engine Exhaust System 77
- Engine Cooling System 78
- Electrical System 81
- Hydraulic System 90
- Header Drive: Hydraulics 93
- Traction Drive: Hydraulics 98
- Steering Checks 99
- MAINTENANCE/SERVICE 100
- Steering Checks (continued) 100
- MAINTENANCE/SERVICE 101
- Troubleshooting 102
- Procedure (continued) 104
- Friction Device Adjustment 105
- Cab Air System 109
- Maintenance Schedule 112
- MAINTENANCE RECORD 114
- (continued) 115
- TROUBLE SHOOTING 116
- Electrical 124
- Traction Drive System 125
- Header Hydraulics 128
- Header Drive 128
- TROUBLE SHOOTING 129
- Header Drive (continued) 130
- Park Brake 130
- Operator's Seat 130
- OPTIONS AND ATTACHMENTS 131
- B2961 – Fore-Aft 131
- B2962 – Header Tilt 131
- UNLOADING 132
- Prepare to Unload 132
- Two Forklift Method 132
- UNLOADING 133
- One Forklift Method 133
- ASSEMBLY 134
- Install Tires 134
- ASSEMBLY 135
- Battery 136
- ASSEMBLY 137
- Adjustments and Checks 137
- Cab Heater 137
- Preparing the Tractor for 138
- 962/963 & 972 Headers 138
- Preparing 972 Harvest Header 141
- Radio Installation 142
- Two-Way Radio Installation 143
- Tool Box 143
- Swath Roller 144
- Self-Propelled Windrower 149
- Pre-Delivery Checklist 149
- Roof Wiring Schematic 151
- Cab Wiring Schematic 152
- Tractor Wiring Schematic 153
- Form 147141/147459 154
Related products and manuals for Gardening equipment Macdon 9352c SP
Gardening equipment Macdon 9352i SP User Manual
(155 pages)
(155 pages)
Gardening equipment Macdon 9250 SP User Manual
(160 pages)
(160 pages)
Gardening equipment Macdon D65 User Manual
(166 pages)
(166 pages)
Gardening equipment Macdon D65 User Manual
(42 pages)
(42 pages)
Gardening equipment Macdon A-30D User Manual
(140 pages)
(140 pages)
Gardening equipment Macdon A40-D User Manual
(193 pages)
(193 pages)
© 2020, manymanuals.com. All rights reserved. | 0.664 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals