Macdon 9250 SP User Manual Page 102
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
100
MAINTENANCE/SERVICE
Traction Drive: Neutral Lock and
Steering Checks (continued)
6. Radius Arm Pivots
: Check the two pivots (A)
and (C). At each pivot, torque inner nut (D) to 7
ft.lbs. (10 N⋅m). Hold inner nut (D) with a
wrench and tighten outer nut (E) against nut
(D). Torque nut (E) to 60 to 70 ft.lbs. (80 to 90
N⋅m).
IMPORTANT: Be sure to hold inner nut (D)
while tightening outer nut (E). Nut (D) MUST
NOT TURN.
At ball joint connection (B), torque both nuts to
60 to 70 ft.lbs. (80 to 90 N⋅m).
7. Ground Speed Lever Position
: Check that when
the steering wheel is locked, the ground speed
lever (F) is centered fore-aft in the neutral
detent on side console as shown.
To adjust:
a. Loosen bolts (G) (see photo above), allowing
bolts to slide in slots.
b. Lock the pintle arms in the neutral lock
adjustment bolts. See check 3.
c. Hold ground speed lever (F) centered fore-aft in
neutral detent.
d. Have a second person tighten bolts (G) as
follows:
- inner nut: 80 to 90 ft.lbs. (110 to 120 N⋅m)
- outer nut: 60 to 70 ft.lbs. (80 to 90 N⋅m)
8. Neutral Lock Structure
: Check for proper
movement of support structure (J) for the
neutral lock adjustment bolts as follows:
a. Disconnect spring (P) to unload pivots.
b. Check that support structure (J) rotates freely.
c. Check that there is no fore-aft movement of
support structure (J).
d. If no adjustment is required, reconnect spring
(P).
To adjust:
a. Turn nut (K) until the washer just contacts the
plastic bushing. This pivot must allow free
rotation of the support structure.
b. Turn nut (L) until the washer contacts the front
support. Check again for free rotation of the
structure with no fore-aft movement. To lock,
hold inner nut (L) with a wrench
and tighten
outer nut (M) against nut (L). Torque nut (M) to
60 to 70 ft.lbs. (80 to 90 N⋅m).
c. Reconnect spring (P).
9. Loose Hardware
: Check all hardware (not
included in the previous checks) is properly
tightened to torque specifications on ground
speed controls, control rods, pump pintle arms
and neutral start mechanisms.
D
E
C
G
A
B
RADIUS ARM
GROUND SPEED LEVER - NEUTRAL DETENT
P
M
L
K
J
NEUTRAL LOCK STRUCTURE
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
Related products and manuals for Gardening equipment Macdon 9250 SP
Gardening equipment Macdon D65 User Manual
(166 pages)
(166 pages)
Gardening equipment Macdon D65 User Manual
(42 pages)
(42 pages)
Gardening equipment Macdon A-30D User Manual
(140 pages)
(140 pages)
Gardening equipment Macdon A40-D User Manual
(193 pages)
(193 pages)
Gardening equipment Macdon 922 User Manual
(84 pages)
(84 pages)
© 2020, manymanuals.com. All rights reserved. | 0.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals