Macdon 9250 SP User Manual download pdf (Page 19)

Form # 46584 Issue 11/06 Web Rev_01

OPERATOR'S STATION

CAUTION: Learn and practice safe

use of controls before operating.

IMPORTANT: See your Dealer if there are any

instrument malfunctions. Operate windrower only if

all instruments work properly.

Mac-Monitor

The LCD display allows the operator to monitor

various machine systems, while the warning lights

and audible tones are provided to alert the

operator that continued operation will cause

serious machine damage.

Six Function LCD displays the following:

• tachometer (engine speed) (B)

• cutting rate (area per hour) (C)

• subtotal area (D)

• grand total area (D)

• engine accumulated hours (E)

• header accumulated hours (F)

Select function by momentarily pressing switch (A)

once for each mode change. The function light for

the current selection will flash for 10 seconds. The

other function lights burn steadily during scrolling

to indicate which functions are currently available

at the present engine speed.

When engine is not running, and key is in the ON

position, subtotal area is the default and

momentarily pressing switch (A) scrolls through

grand total area, engine hours, header hours and

back to subtotal area.

When engine is running at less than 2000 rpm,

tachometer is the default and momentarily

pressing switch (A) scrolls through all six functions.

After 10 seconds in any mode, the monitor

switches back to tachometer.

When engine speed is greater than 2000 rpm,

tachometer is the default and momentarily

pressing switch (A) scrolls through cutting rate,

subtotal area and back to tachometer. Tach or

cutting rate will remain displayed until switch is

pressed, while subtotal area will revert back to

tachometer after 10 seconds

TACHOMETER (B):

Indicates engine speed in revolutions per minute.

CUTTING RATE (Area per hour) (C):

Displays in either acres or hectares. Calculates

rate of crop cut when header is engaged and

engine rpm exceeds 2000 rpm based on ground

speed and programmed cut width.

SUBTOTAL/GRAND TOTAL CUT AREA (D):

Displays in either acres or hectares. Subtotal cut

area will display first. This shows area cut since

last reset. When in this mode hold the button for

5 seconds to reset the subtotal to zero.

Grand total cut area shows total area cut over

life of the windrower. After 9999, display will

flash back and forth between thousand units and

hundred units. For example, 53286 would be

displayed by flashing between 53_ and _286,

while 573902 would be displayed by flashing

between 573_ and _902.

ENGINE HOUR METER (E):

Accumulates time that the engine is running. The

display will alternate between 4 digits

(representing hours accumulated) and tenths of an

hour.

HEADER HOUR METER (F):

Accumulates time that the header is engaged with

the engine running. The display will alternate

between 4 digits (representing hours accumulated)

and tenths of an hour.

PROGRAMMING

To ensure cutting rate, cut area and speedometer

display correctly, program the monitor for units of

measure, cut width and tire size as follows:

1. Turn the ignition key to the off position

2. Depress and hold switch (A) while turning the

key to the on position to enter programming

mode, then release switch.

NOTE: Programming mode works only if engine is

not running.

3. Momentarily press switch (A) to scroll through

these programming modes: “ENG/SI”,

“CUT WIDTH” and “TIRE SIZE”. Do not hold

switch for more than 5 seconds. The active

selection within each mode flashes on the

display.

Continued next page.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 159 160

Comments to this Manuals

No comments

Macdon 9250 SP User Manual Page 19

Comments to this Manuals

Related products and manuals for Gardening equipment Macdon 9250 SP