Macdon 9250 SP User Manual Page 27
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
25
OPERATOR'S STATION
Header Controls (continued)
CUT HEIGHT INDICATOR
(G) - The gauge on the
lift linkage can be used to identify desired cut
heights.
With the center link (between tractor and header)
in a mid-range position, the numbers on the gauge
indicate approximate cut (stubble) height in inches.
Adjusting center link length will affect the starting
point; eg. gauge reading 4 may indicate a 3"
(longer center link) or 5" (shorter center link) cut
height. However, the difference between gauge
readings of 4 and 8, 8 and 12, etc. will always be
about 4 inches, regardless of center link length.
Header Angle
: Cut height indicator (G) can also
be used to identify header angle when cutting with
header on the ground. The gauge indicator will
decline until header contacts ground, then as
header height switch is held in down position, the
indicator reading will increase as header angle
steepens. The gauge numbers will not correspond
to actual header angle, but can be used to identify
a desired setting. See "Header Angle" in Operation
section for adjustment procedure.
Seat Belts
The windrower is equipped with a seat belt on the
Operator’s and Trainer’s seats.
WARNING: Before starting engine,
securely fasten your seat belt and
ensure trainer’s seat belt is fastened
if occupied. The seat belt can help insure your
safety if it is used and maintained. Never wear
a seat belt loosely or with slack in the belt
system. Never wear the belt in a twisted
condition or pinched between the seat
structural members.
To fasten seat belt, pull belt completely across
your body. Push the metal eye into the buckle until
it locks. Adjust the position of the belt as low on
your body as possible.
To release, push the red button in the end of the
buckle and separate the buckle and metal eye.
G
CUT HEIGHT INDICATOR
SEAT BELT
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
Related products and manuals for Gardening equipment Macdon 9250 SP
Gardening equipment Macdon D65 User Manual
(166 pages)
(166 pages)
Gardening equipment Macdon D65 User Manual
(42 pages)
(42 pages)
Gardening equipment Macdon A-30D User Manual
(140 pages)
(140 pages)
Gardening equipment Macdon A40-D User Manual
(193 pages)
(193 pages)
Gardening equipment Macdon 922 User Manual
(84 pages)
(84 pages)
© 2020, manymanuals.com. All rights reserved. | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals