MacDon 9352 Operator's Manual Page 109
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
107
MAINTENANCE/SERVICE
Traction Drive: Wheels and Tires
TIRE INFLATION
Make a visual check daily
that tires have not lost
pressure. Under-inflation of drive tires can cause
side wall cracks.
Once a year
, measure tire pressure with a gauge.
Maintain the pressures recommended on page 12
(Specifications Section).
WARNING: Service tires safely. A tire
can explode during inflation and
cause serious injury or death. Never
increase air pressure beyond 35 psi
(240 kPa) when seating the bead on the rim.
Replace a tire if it has a defect. Replace a
wheel rim which has cracks, wear or severe
rust. Never install a tube in a cracked wheel
rim. Never weld a wheel rim. Make sure all the
air is removed from a tire before removing the
tire from the rim. Never use force on an inflated
or partially inflated tire. Make sure the tire is
correctly seated before inflating to operating
pressure.
Do not remove, install or make repairs to a tire
on a rim unless you have the proper equipment
and experience to perform the job. Take the tire
and rim to a qualified tire repair shop. If the tire
is not in correct position on the rim, or if too
full of air, the tire bead can loosen on one side,
causing air to leak at high speed and with great
force. An air leak of this nature can thrust the
tire in any direction, endangering anyone in the
area.
(A) - Use a safety cage if available.
(B) - Do not stand over tire. Use a clip-on chuck
and extension hose.
16.5 CASTER ANTI-SHIMMY SPRINGS
Maintain a spring length of 89 to 92 mm (3-1/2 to
3-5/8"). If necessary add 3/4 SAE flatwashers
under spring to achieve this dimension. See
Assembly section, page 135.
SHORTENING THE WHEEL BASE
The tractor unit’s wheel base can be shortened
from 128 inches (3244 mm) to 113 inches (2864
mm) by reversing the walking beam. This work
should be done by a qualified dealer.
JACKING PROCEDURE
Position jack or jack stand under bracket (C)
welded to tractor frame legs, ensuring head of jack
is secured by keeper rod.
SERVICE TIRES SAFELY
C
JACK POSITION
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
© 2020, manymanuals.com. All rights reserved. | 2.945 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals