MacDon 9352 Operator's Manual download pdf (Page 20)

Form # 46584 Issue 11/06 Web Rev_01

G H

INDICATOR

OPERATOR'S STATION

Mac-Monitor:

PROGRAMMING (continued)

4. Once the desired programming mode is

displayed, enter the selection mode by pressing

and holding switch (A) for more than 5 seconds.

(At 5 seconds there will be an audible tone.

Release switch at tone.)

5. In the “ENG/SI” selection mode the monitor

shows “ENG” or “SI”, whichever unit of measure

is active. To scroll between the two, momentarily

push switch (A). “SI” will cause cutting rate and

cut area totals to display in hectares. As well, the

speedometer will display in kilometers per hour.

When in “SI”, the small triangle at the top left

corner of the digital display will be illuminated.

“ENG” will cause cutting rate and cut area totals

to display in acres and the speedometer to

display in miles per hour. Shipping Position =

ENG.

6. To select either “ENG” or “SI” once it is

displayed, press and hold switch (A) for more

than 5 seconds. (At 5 seconds there will be an

audible tone. Release switch at tone.) This also

advances the monitor to the next programming

mode (CUT WIDTH).

7. Press switch (A) for 5 seconds again to enter the

“CUT WIDTH” selection mode. The monitor

shows the active cut width. To scroll through the

cut widths, momentarily press switch (A) to scroll

in 0.5 foot increasing increments through a

cutting range of 10.0 to 37.0 feet (3.05 to 11.28

meters). Display in feet will have an “F” following

the width, e.g. 24.5 feet cutting width would be

shown as “24.5F”. Shipping Position = 10.0F

NOTE: To advance the cut width in increments

of 5 feet instead of 0.5, turn the header drive

switch on and off again (see page 23).

8. To select a cut width once it is displayed, press

and hold switch (A) for more than 5 seconds. (At

5 seconds there will be an audible tone. Release

switch at tone.) This also advances the monitor

to the next programming mode (TIRE SIZE).

9. Press switch (A) for 5 seconds again to enter the

“TIRE SIZE” selection mode. The monitor shows

the active tire size. Momentarily press switch (A)

to scroll through tire options. This selection will

trigger the correct readout for speedometer,

based on rolling diameter of each tire size.

Shipping Position = 21.5. NOTE: For units with

500 series tires, select the “500” option.

10. To select a tire size once it is displayed, press

and hold switch (A) for more than 5 seconds. (At

5 seconds there will be an audible tone. Release

switch at tone.) This also returns the monitor to

the “ENG/SI” programming mode.

11. To save the settings into memory and return the

monitor into the normal working mode, turn the

key to the “off” position and back on again. This

can be done from any of the three main

programming modes (ENG/SI, CUT WIDTH,

TIRE SIZE), but not from the selection mode

within any of these.

Mac-Monitor Machine Warning System:

Consists of individual lights to indicate low engine

oil pressure, low transmission oil pressure and

park brake on. An audible tone will sound

whenever one of the indicator lights is on. In

addition, the tone will sound when a high engine

coolant temperature is indicated.

ENGINE OIL PRESSURE LIGHT (G):

Both light and tone will be activated when ignition

switch is turned ON if engine oil pressure is below

11 psi (75 kPa). If light and tone stay on for more

than a few seconds after engine starts, or if they

activate while engine is running, shut engine off

and check engine oil level.

TRANSMISSION OIL PRESSURE LIGHT (H):

Both light and tone will be activated when ignition

switch is turned ON if transmission oil pressure is

below 150 psi (1035 kPa) for Turbo or 40 psi (275

kPa) for Naturally Aspirated engine. Do not drive

the windrower until light and tone go off. If light and

tone stay on after engine starts, or if they activate

during operation, shut engine off and check

hydraulic oil level at reservoir. If oil level is

adequate, measure supercharge relief pressure.

See "Traction Drive: Hydraulics" in Maintenance/

Service section.

PARKING BRAKE LIGHT (J):

Both light and tone will be activated when ignition

switch is turned to ON as a reminder to release

brake before driving windrower. Release of brake

de-activates light and tone. Light and tone will not

activate with transmission in neutral.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 159 160

Comments to this Manuals

No comments

MacDon 9352 Operator's Manual Page 20

Comments to this Manuals