MacDon 9352 Operator's Manual Page 138
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
136
REAR CASTER INSTALLATION: 9.5 TIRES
ON XX50/XX40 TRACTORS
ASSEMBLY
Install Tires
9.5 REAR TIRES on XX50/XX40 Model Tractors:
(Forked or Formed Casters)
1. Lift rear end of windrower with forklift and
remove yellow shipping support from walking
beam (see B on page 135). Replace bolts
securing walking beam pivot tube bracket and
torque to 390 N⋅m (290 ft.lbs.).
2. Install casters in rear beam as shown.
NOTE: When installing rear casters, ensure that
smaller I.D. race of thrust bearing (A) is towards
caster.
3. Place rear casters in the outboard position
(extending behind rear beam) and lower rear of
windrower to ground.
4. Set caster tire pressure at 10 psi (70 kPa).
16.5, 11-16 or 7.5 REAR TIRES on Model 9352,
4952, 2952, 8152 Tractors
1. Lift rear end of windrower with forklift and
remove yellow shipping support from walking
beam (see B on page 135). Replace bolts
securing walking beam pivot tube bracket and
torque to 390 N⋅m (290 ft.lbs.).
2. Liberally apply multi-purpose grease to bottom
surface of spring assembly (C). Install
assembly (C) over caster pivot shaft.
3. Place one bushing (D), flared edge down, onto
caster pivot shaft
4. Install caster (E) into walking beam by raising
the caster and lowering walking beam onto
pivot shaft. NOTE: Ensure tabs (J) on spring
assembly engage slots in bottom of walking
beam.
NOTE: For 7.5 formed casters, elbow of caster
should be to the outside.
5. Place a second bushing (F), flared edge up,
into walking beam.
6. Place cap (G) on top of assembly and secure
with two 1/2 x 1 inch hex head bolts, and lock-
washers, ensuring bolts engage threaded holes
in top of caster pivot shaft. Tighten bolts to 75
ft. lbs. (102 N·m).
7. Place transport lock pin (H) into storage
position and secure with hairpin.
8. Repeat steps 2 to 7 at other caster.
9. Grease the caster pivots with multi-purpose
grease, continuing until grease is forced out top
of walking beam.
10. Place rear casters in the outboard position
(extending behind walking beam) and lower
windrower to ground.
11. Set caster tire pressure at 10 psi (70 kPa) for
16.5 or 11-16 tires and 19 psi (132 kPa) for 7.5
tire.
NOTE: For 16.5 and 11-16 rear tires, factory
set pressures are higher than recommended
operating pressure. Deflate to 10 psi (70 kPa).
REAR CASTER INSTALLATION
ON 9352/4952/2952/8152 TRACTORS
C
D
E
F
G
H
H
J
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
© 2020, manymanuals.com. All rights reserved. | 0.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals