MacDon 9352 Operator's Manual Page 68
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
66
MAINTENANCE/SERVICE
Diesel Engine
LUBRICATING OIL
Changing engine oil and filter
(continued)
6. Install the new filter. Turn the filter onto the
mount until the gasket contacts the filter head.
Tighten the filter an additional 1/2 to 3/4 turn by
hand.
IMPORTANT: Do not use a filter wrench to
install the oil filter. Over-tightening can damage
the gasket and the filter.
7. Install the oil pan drain plug.
8. Fill the engine at (A) with the proper amount of
oil. See "Fuels, Fluids and Lubricants" section
for recommended oil types.
Capacity
Diesel Engine
With filter change 11 US qts (10.4L)
Without filter change 10 US qts (9.5L)
9. Operate the engine at low idle and check for
leaks at the filter and drain plug.
10. Shut off engine. Wait five minutes, then check
oil level at dipstick. If required, add or drain oil
to bring level to high mark.
DIESEL ENGINE BELTS
The alternator/water pump/fan belt is automatically
tightened. No manual adjustment is required. See
installation procedure at right.
NOTE: When installing new compressor belt (G),
never pry belt over pulley. Loosen necessary
hardware and adjust belt tension. Re-adjust
tension of a new belt after a short run-in period.
(About 5 hours.)
To adjust compressor belt:
1. Loosen compressor mounting hardware.
2. Adjust tension so that a force of 8 to 12 lbs. (35
to 55 N) deflects belt 3/16 inch (5 mm) at mid-
span.
3. Tighten compressor mounting hardware and
recheck tension.
A - Air Conditioning Compressor
B - Alternator
C - Water Pump
D - Fan Pulley
E - Crankshaft Pulley
F - Automatic Belt Tightener
G - Compressor Belt
H - Alternator/Water Pump/Fan Belt
NOTE: For easiest installation of new belt (H):
Install around pulleys (E), (D), and (B), then raise
tensioner (F) and install on pulley (C). Lower
tensioner and check belt is properly seated in all
pulley grooves.
BELTS - DIESEL ENGINE
B
C
D
E
F
G
A
H
A
OIL FILLER LOCATION
(view from right side of windower)
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
© 2020, manymanuals.com. All rights reserved. | 0.163 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals