MacDon 9352 Operator's Manual Page 113
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
111
MAINTENANCE/SERVICE
Cab Air System
RETURN AIR FILTERS
Clean return air filters every 100 hours
, more often
in dusty conditions.
To clean:
1. Remove filter covers at both sides of cab rear
wall by removing two nuts (A).
2. Remove foam filter elements and clean with
compressed air.
3. Replace filter elements and covers.
EVAPORATOR CORE
If air conditioning system produces insufficient
cooling, a possible cause is clogged evaporator
fins. Fins will clog up starting at the back side of
the evaporator core (against cab wall).
Evaporator core access and cleaning:
1. Remove R/H console side panel (A).
2. Remove nut securing seat support panel to
mount on door side.
3. Release air suspension to fully lower operator's
seat. Tilt seat (B) forward while tilting seat-back
(C) rearward until seat is vertical.
4. Lift the acoustical foam (E) at top of evaporator
core and remove two nuts securing retainer (F).
Remove retainer.
5. Tilt evaporator core forward and vacuum off
back side of core (at cab wall). Use a fin
straightener to loosen clogs.
6. Blow compressed air through core at an angle
parallel to tubing alignment as shown. To
prevent fin damage, blow air directly at fin
edges, not at flat face.
7. If the compressed air can not be felt at the back
of the core, proceed as follows:
• Remove foam filter (D) from drain tray and
clean with warm water.
• With filter (D) still out, pour warm water down
through the core and leave it to soak. (The
drain tray will catch and remove run-off.)
8. Blow compressed air through the core as in
step 6. Repeat warm water soaking as required
until air blows through evaporator core freely.
9. Straighten any bent fins and reassemble.
WARNING: To avoid cuts from
evaporator fins, do not use bare
hands to brush away clogs.
A
REMOVE FOR ACCESS TO
RETURN AIR FILTER
EVAPORATOR CORE ACCESS & CLEANING
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
© 2020, manymanuals.com. All rights reserved. | 0.341 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals