MacDon 9352 Operator's Manual Page 100
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
98
MAINTENANCE/SERVICE
Traction Drive: Neutral Lock and
Steering Checks
DANGER: To prevent machine run-
away:
• STOP ENGINE before adjusting steering
linkage or neutral interlock.
• Never rewire or misadjust neutral interlock
so engine can be started with controls out
of neutral.
• Never start engine by shorting across
starter terminals. Machine will start with
drive engaged and move if normal starting
circuitry is bypassed.
• Start engine only from operator's seat.
Never try to start engine with someone
under or near machine.
• Refer to proper start-up procedure in
Operation section.
A properly functioning system should operate as
follows:
• The starter should engage ONLY
when the
ground speed lever is in neutral, the steering
wheel is locked, and the header drive switch is
in the off position.
• Under these conditions, the machine should
not move after engine start-up.
If either of the above does not hold true, perform
the following nine checks. Adjustments, if required
are described following each check point. A
troubleshooting section follows the checklist.
DANGER: To avoid severe personal
injury or death caused by machine
runaway, shut off engine and
remove key before performing any
of the following checks and/or
adjustments.
1. Neutral Start Switch
: Check that electrical
connections are good at neutral start switch (A).
With controls in start-up position as described
above, plunger of switch must be compressed.
Adjust switch support if required. Do not over-
adjust switch support, as this will prevent pintle
arms from locking as described in Check # 3.
2. Header Drive Belt Switch:
Check that electrical
connections are good at header drive belt
switch (B). With controls in start-up position,
(belt disengaged), plunger of switch must be
compressed. Adjust switch support if required.
FOLLOW ADJUSTMENT PROCEDURE
A
NEUTRAL START SWITCH
B
HEADER DRIVE BELT SWITCH
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
© 2020, manymanuals.com. All rights reserved. | 0.286 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals