MacDon 9352 Operator's Manual Page 101
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
99
MAINTENANCE/SERVICE
Traction Drive: Neutral Lock and
Steering Checks (continued)
3. Neutral Lock Adjustment Bolts Engagement
:
Check the depth of engagement of the neutral
lock adjustment bolts (B) on pintle arms (C).
Minimum engagement is 3/8 inch (10 mm), that
is, the full diameter of the bolt must contact
pintle arms.
To adjust:
a. Loosen cable as described in check 4, below.
b. Adjust neutral start switch to obtain proper
engagement depth.
c. Readjust cable as described in check 4.
WARNING: Do not adjust the neutral
lock adjustment bolts (B). These
bolts can only be adjusted during
neutral set-up procedure described
at the end of this section.
4. Cable Tension
: Check tension of cable (D). The
cable should be tight when the ground speed
lever (F) is at the right hand side of the neutral
detent on side console, and when the neutral
start switch is fully compressed. If the cable is
too tight, it will prevent the neutral start switch
from fully compressing and prevent proper
engagement of adjustment bolts on pintle arms.
To adjust cable tension, loosen nut (H) on
threaded hook bolt (E) and turn nut (J)
clockwise to increase cable tension, counter-
clockwise to decrease. Tighten nut (H) against
nut (J) to secure the position.
5. Ground Speed Lever Pivot
: Check the pivot at
ground speed lever (F). Nut (L) should be flush
with the end of the carriage bolt (full thread
engagement). To tighten, hold nut (K) with a
wrench and tighten nut (L) against nut (K).
Torque nut (L) to 60 to 70 ft.lbs. (80 to 90 N⋅m).
ENGAGEMENT DEPTH:
NEUTRAL LOCK ADJUSTMENT BOLTS
GROUND SPEED LEVER CONNECTIONS
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
© 2020, manymanuals.com. All rights reserved. | 0.206 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals