MacDon 9352 Operator's Manual Page 43
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Form # 46584 Issue 11/06 Web Rev_01
41
OPERATION
Attaching the Header (continued)
6. Connect driveline to header drive shaft as
follows:
• Open hinged shield at header drive shaft.
• Pull back spring loaded collar (G) on
driveline yoke and slide yoke onto header
shaft. Release collar, ensuring yoke locks
in position on shaft.
• Attach chain hook (if present) to hinged
shield at (H).
• Close hinged shield.
NOTE: For 962/963 Header only, attach chain
hook (if present) to shield (J) on connector shaft as
below.
7. Hydraulic Hose Connections:
910 Series Headers: No hydraulic connections
between header and tractor. Couple (A) to (B)
and (D) to (E) for these units. Failure to do so
will cause header drive circuit to overheat,
causing potential hydraulic component failure or
product performance problems.
920 & 930 Series Headers
: Two connections
are made at couplers (A) and (B) at the header
right hand leg. One connection is made at
coupler (D) at the header left hand leg. For 912
& 922 Headers with Hay Conditioner equipped
with Hydraulic Roll Opener cylinders, connect
hose from these cylinders at coupler (C).
940, 960 & 970 Series Headers
: Two
connections are made at couplers (A) and (B) at
the header right hand leg. Two connections are
made at couplers (C) and (E) at the tractor left
hand leg. One connection is made at coupler
(D) at the header left hand leg.
A - reel drive pressure
B - reel drive return
C - reel lift (or Hay Conditioner Roll Opener
cylinder circuit, if equipped)
D - conveyor drive pressure
E - conveyor drive return
8. Connect the header electrical wiring harness at
connector (F).
A
B
HYDRAULIC CONNECTIONS - R/H SIDE
D
F
C
E
HYDRAULIC & ELECTRICAL CONNECTIONS
L/H SIDE
CONNECT DRIVELINE –
912/922/933/972 HEADERS
G
H
J
CONNECT DRIVELINE – 962/963 HEADER
- 9250/9350/9352 1
- SELF-PROPELLED 1
- WINDROWER 1
- Proposition 65 Warning 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- SERIAL NUMBER LOCATIONS 7
- SAFETY 10
- SPECIFICATIONS 13
- SPECIFICATIONS 14
- TORQUE SPECIFICATIONS 15
- TORQUE SPECIFICATIONS 16
- OPERATOR'S STATION 17
- Symbol Definitions 17
- OPERATOR'S STATION 19
- Mac-Monitor 19
- Mac-Monitor: 20
- Operator Presence System 21
- Speedometer 21
- Ignition Switch 22
- OPERATOR'S STATION 23
- Cab Temperature Controls 23
- Windshield Wiper Control 23
- Windrower Controls 24
- Header Controls 25
- Header Controls (continued) 26
- Seat Belts 27
- Seat Adjustments 28
- Operator Amenities 29
- OPERATION 30
- To the New Operator 30
- Break-in Period 31
- OPERATION 32
- Pre-Starting Checks: Annual 32
- Pre-Starting Checks: Daily 33
- Start-Up Procedure 34
- Driving the Windrower 36
- Stopping Procedure 40
- Leaving the Windrower 41
- Attaching the Header 42
- (continued) 44
- Adding Rear Weight 45
- Detaching the Header 47
- Header Angle 50
- HEADER TILT HYDRAULIC 50
- ADJUSTMENT 50
- Header Levelling 51
- Header Flotation 52
- Transporting the Windrower 53
- Storage Procedure 58
- Service Procedures 59
- Fuels, Fluids and Lubricants 61
- 50 Hours (continued) 64
- 200 Hours or Annually 65
- Diesel Engine 67
- Diesel Engine (continued) 69
- Diesel Engine: Fuel System 73
- Engine Exhaust System 78
- Engine Cooling System 79
- Electrical System 82
- Hydraulic System 91
- Header Drive: Hydraulics 94
- Traction Drive: Hydraulics 99
- MAINTENANCE/SERVICE 100
- Steering Checks 100
- MAINTENANCE/SERVICE 101
- Steering Checks (continued) 101
- Troubleshooting 103
- Procedure (continued) 105
- Friction Device Adjustment 106
- AT HALF-WEAR STAGE 110
- MAINTENANCE/SERVICE 111
- Traction Drive: Park Brake 111
- Cab Air System 112
- Maintenance Schedule 115
- MAINTENANCE RECORD 117
- (continued) 118
- TROUBLE SHOOTING 119
- Electrical 127
- Traction Drive System 128
- Header Hydraulics 131
- Header Drive 131
- TROUBLE SHOOTING 132
- Header Drive (continued) 133
- Park Brake 133
- Operator's Seat 133
- OPTIONS AND ATTACHMENTS 134
- UNLOADING 135
- Prepare to Unload 135
- Two Forklift Method 135
- UNLOADING 136
- One Forklift Method 136
- ASSEMBLY 137
- Install Tires 137
- ASSEMBLY 140
- Battery 140
- ASSEMBLY 141
- Adjustments and Checks 141
- Cab Heater 141
- Preparing the Tractor for 142
- Preparing 972 Harvest Header 145
- Radio Installation 146
- Two-Way Radio Installation 147
- Tool Box 147
- Swath Roller 148
- INDEX 150
- Self-Propelled Windrower 153
- Pre-Delivery Checklist 153
- Roof Wiring Schematic 155
- Cab Wiring Schematic 156
- Tractor Wiring Schematic 157
© 2020, manymanuals.com. All rights reserved. | 0.208 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals